| HOME | COMPARISION OF FLAT HEATER EXISTING TECHNOLOGIES | HOW TO ORDER | CONTACT US & LOCATION | DISTRIBUTORS & AGENTS | WARRANTY & SALES CONDITIONS |  |
 |
|---|---|---|---|---|---|---|---|
| ULTIMHEAT : Products range (controls) |
|---|
 Type IBSurface mounting thermostats. Main features: Precise and adjustable surface temperature control on heating plates, silicone heating pads, foil heaters, temperature range from 20 to 300° See more of this product Download PDF  Access full catalogue |
 Type 35EREnergy regulators. Main features: Energy regulators are used to adjust power on electrical heaters. Connected in line with electrical heaters, they provide adjustable cycling sequence, thus adjusting average electrical power See more of this product Download PDF Access full catalogue |
 Type 8GSingle pole control bulb and capillary thermostat. Main features: Adjustable remote temperature control. Liquid filled bulb. Numerous temperature range from -35°C to +320°C used in single pole circuit See more of this product Download PDF Access full catalogue |
 Type 8C3 pole control bulb and capillary thermostats. Main features: Adjustable remote temperature control. Liquid filled bulb. Numerous temperature range from -35°C to +320°C used in 3 poles circuits See more of this product Download PDF Access full catalogue |
 Type 1BRod thermostats. Main features: Temperature control of liquids and gas, with DPST or SPDT contact. Numerous temperature range from -10°C to +165°C See more of this product Download PDF Access full catalogue |
 Type 2PEElectronic thermostat. Main features:This electronic thermostat for incorporation has been designed to replace electromechanical thermostats. It is mounted with two screws M4 at the same distance 28 mm, uses a 6mm dia. shaft with 4.6mm flat with the same length, and its rotation angle is 270 °. The temperature ranges are the same as the bulb and capillary thermostats. It additionally features adjustable temperature differential, and heating or cooling relay output setting, and control or manual reset action can be set. See more of this product Download PDF Access full catalogue |
 Type 2DNDigital display electronic controller. Main features: This electronic temperature controller with the simplest and the most instinctive setting by end user was designed for easy incorporation inside cabinets with DIN rail mounting. It can be used by untrained operators. It provides simple On Off action temperature control. End user has access to set point and differential setting only. It is possible to set °C or °F display, heating or cooling relay output, decimal display, sensor type and temperature range by internal Dip switches (Without access by end user). Adjustment of maximum temperature can be set without need to open the control. Pt100 and NTC sensors See more of this product Download PDF Access full catalogue |
 Type 4C3 pole manual reset disc thermostats. Main features:Temperature limit of heaters, instant water heaters, saunas steam generators, industrial heaters. Used in 3 pole circuits See more of this product Download PDF Access full catalogue |
 Type 823 pole manual reset high limit thermostat. Main features: Fail safe, manual reset, with capillary length 250mm or 900 mm, 3 pole contacts open on temperature rise temperature range from 60°C to 170°C See more of this product Download PDF Access full catalogue |
 Type LSAdditional thermostat shaft switch, 20A 250-400V Main features: These on-off switches are designed to be added on thermostat shafts. They provide off position when the thermostat shaft is at the minimum position. They are available in single pole contact, two pole (one level) and three pole or four-pole contact (two levels). See more of this product Download PDF Access full catalogue |
 Type LTLT Type On-off rotary switch, 20A 250-400V Main features: These on-off switches are designed for heater power switching. They are available in single pole contact, two pole (one level) and three pole or four-pole contact (two levels). See more of this product Download PDF Access full catalogue |
 Type KProfessional applications bulb and capillary thermostat. Main features: Heavy duty , temperature ranges up to 760°C, SPDT 15A 250-400V. Also exists with SPDT manual reset. See more of this product Download PDF Access full catalogue |
 Type Y02NCabinet thermostat DIN rail mounting. Main features: These models have been designed to control the temperature inside electrical cabinets, being mounted on their DIN rail. Their SPDT contact allows their use to control a cabinet heater, a fan or a filter fan, or a cooling system. Temperature range -10+50, to +20+80°C See more of this product Download PDF Access full catalogue |
 Type Y03IP44 housing bulb and capillary thermostat. Main features: SPDT contact, external knob, liquid filled bulb, distance measurement with capillary. Adjustment ranges: -35+35°C (-30+95°F), 4-40°C (40-105°F), 30-90°C (85-195°F), 30-110°C (90-230°F), 50-200°C (120-390°F), 50-300°C (120-570°F) Mounting: Wall mounting, by two side lugs with holes for dia.4 mm screws, 62 mm distance. See more of this product Download PDF Access full catalogue |
 Type Y04IP44 housing rod thermostat. Main features: SPDT contact, external knob, liquid filled rod, located inside a backside mounted 304L stainless steel pocket. Adjustment ranges: -35+35°C (-30+95°F), 4-40°C (40-105°F), 30-90°C (85-195°F), 30-110°C (90-230°F) Mounting: by the ½”BSPT pocket fitting See more of this product Download PDF Access full catalogue |
 Type Y05IP44 housing rod thermostat, for swimming pools. Main features: SPDT contact, external knob, liquid filled rod, located inside a backside mounted plastic pocket. Adjustment ranges: 4-40°C(40-105°F) Mounting: by the ½”NPT pocket fitting See more of this product Download PDF Access full catalogue |
 Type Y1AIP65 aluminum enclosure ambient temperature thermostat. Main features: - Wall mounting for indoor temperature control of cold room - Temperature control of industrial or commercial premises. - Outdoor temperature control of antifreeze heaters, - Green houses and livestock stables temperature control Withstand very low ambient temperatures Temperature range: numerous from-25 to +70°C See more of this product Download PDF Access full catalogue |
 Type Y1GKIP65 aluminum enclosure bulb and capillary thermostat. Main features: Remote control in usual industrial application and environment, not hazardous areas. Internal adjustment is convenient for products that must not be frequently adjusted. Withstand very low ambient temperatures Long electrical and mechanical life model Temperature range: numerous from -25 to +760°C See more of this product Download PDF Access full catalogue |
 Y1G8IP65 aluminum enclosure bulb and capillary thermostat. Main features: Remote control in usual industrial application and environment, not hazardous areas. Internal adjustment is convenient for products that must not be frequently adjusted. Standard electrical and mechanical life model Temperature range: numerous from -35 to +320°C See more of this product Download PDF Access full catalogue |
 Y1R8IP65 aluminum enclosure Rod thermostat. Main features: These liquid expansion rod thermostats can be installed inside pockets as immersion thermostats in pipelines and containers, and for monitoring temperature in air ducts, in usual industrial application and environment. (Not suitable for hazardous areas). - Internal adjustment is convenient for products that must not be frequently adjusted. - Insensibility to strong vibrations Standard electrical and mechanical life model Temperature range: numerous from 4 to +350°C See more of this product Download PDF Access full catalogue |
 Y108IP65 aluminum enclosure, for pipes, surface temperature control. Main features: Pipe surface temperature control in usual industrial application and environment, (Not suitable for hazardous areas) Internal adjustment is convenient for products that must not be frequently adjusted. Standard electrical and mechanical life model See more of this product Download PDF Access full catalogue |
 Type Y22Thermostats with IP65 plastic housings, for heat tracing. Main features: In these boxes, the thermostat, bimetal disc type, is over-molded, and is thermally insulated from the wall on which it is mounted. Its temperature sensing cup is mechanically protected by a grid. It is located in front of the enclosure to be in an area of natural circulation of air. See more of this product Download PDF Access full catalogue |
 Type Y303Immersion heaters connection boxes 78x66x50 mm. Material: Die cast aluminum Type Universal, unlosable stainless steel fasteners, galvanic corrosion protected See more of this product Download PDF Access full catalogue |
 Type Y304Immersion heaters connection boxes 78x78x74 mm. Material: Die cast aluminum Type Unlosable stainless steel fasteners, galvanic corrosion protected See more of this product Download PDF Access full catalogue |
 Type Y305Immersion heaters connection boxes 105x105x96 mm. Material: Die cast aluminum Type Universal, unlosable stainless steel fasteners, galvanic corrosion protected See more of this product Download PDF Access full catalogue |
 Type Y306Immersion heaters connection boxes Dia. 100x100 mm. Material: Fiber glass reinforced PA66 Type Universal, unlosable stainless steel fasteners See more of this product Download PDF Access full catalogue |
 Type Y309Immersion heaters connection boxes 182x132x144 mm. Material: Die cast aluminum Type Universal, unlosable stainless steel fasteners Many versions of this box size, fully equipped and wired are described in the catalog No. 3, series Y7. See more of this product Download PDF Access full catalogue |
 Type Y5FHand held or wall mounting digital temperature controller. Main features: This control box has the smallest footprint and the lowest price of the Y range with waterproof enclosure. It has a modern and aesthetic design, and the same professional concept than other products of this range. Because of their small size (120 x 70 x 40 mm), these controls can be wall mounted with 2 screws 55 mm distance, hand held or just simply laid on the working table. See more of this product Download PDF Access full catalogue |
 Type 9BBJOSilicone boots and grommets for applications in heating equipment and thermostats boots. Thermostats boots Main features: They are designed to protect thermostats against accidental contact or liquids ingress. Depending on the model, they can be filled with resin or simply be glued or vulcanized on their support See more of this product Download PDF Access full catalogue |
 Type 9BBRAImmersion heaters brass fittings. Main features: - Fittings for incorporation by immersion heater manufacturers - Fit the full range of immersion heater enclosures - Compact size and short length result in reduced weight ( save + / -30% compared to double thread fittings) - The fitting thread lengths allow throw wall mounting with fiber gasket and nut on wall of 6 mm thickness (9 mm for 2” and above) or on threaded socket with gasket - Allows a 360° rotation of enclosure when mounted with their rotation ring See more of this product Download PDF Access full catalogue |
 Types Y6,Y7,Y8Industrial temperature controls. Main features: These products come in 4 different dimensional configurations, in control (One sensor) or control + high limit safety (2 sensors or one sensor + one bulb) electronic or thermostat control Temperature range:numerous from -35 to +760°C See more of this product Download PDF Access full catalogue |
 Type 273Electronic intelligent controller, on off action. Main features: Mini-sized and integrated intelligent controller, with very simple end-user interface: Change of set point is made without password, with up and down keys. 10 or 16A output relay. 220 - 240V power supply Sensor: NTC, Pt100, K thermocouple See more of this product Download PDF Access full catalogue |
 Type KAAExplosion proof bulb and capillary thermostats for incorporation Temperature control, front mounting. Main features: These thermostats are intended to monitor or control temperatures in hazardous areas. They can be used in zones 1 or 2 with gas, smoke and fog, class IIC, surface temperature T6, and for ambient temperature on housing of -50 to +80°C. This thermostat uses a flameproof micro-switch type II2Gb, Ex dIIC . The thermostat must be installed in an increased safety enclosure, type Ex-“e”, and electrical connections at the end of the wires must be made inside this EX-“e”enclosure. The thermostat capillary exit must be performed by a cable gland with gasket adapted to the diameter of the capillary and providing the level of protection required by the standard. Temperature range:numerous from -25 to +300°C Exists also with DIN rail mounting See more of this product Download PDF Access full catalogue |
 Type Y90-GExplosion proof thermostats with IP54 aluminum enclosure, cable output Bulb and capillary thermostat, SPDT, 5A 250V, cable connection. Main features: This thermostat uses a flameproof micro-switch type Ex II2G (Ex dIIC T6 Gb). It is installed in a waterproof aluminum enclosure with an ingress protection class IP54, grey epoxy painted RAL 7032, fitted with a built in electrical connection cable. It is not allowed to make electrical connections inside this aluminum enclosure. Electrical connection at the end of this cable must be made inside an increased safety "e" junction box complying with the standard EN60079-7, or outside hazardous area. Aluminum enclosure earthing is mandatory. Temperature range:numerous from -25 to +300°C See more of this product Download PDF Access full catalogue |
 Type Y94Explosion proof thermostats and limiters, connection inside EX « e » aluminum housing with built-in connection block. Bulb and capillary thermostat. Main features: They are intended to monitor or control the temperatures in hazardous areas. Thermostat, housing and terminal block are indivisible. In gas explosive atmospheres, they can be used in zones 1 or 2 in the presence of gas, smoke and fog, class IIC, surface temperature T6, and ambient temperature on the enclosure from -50 to +60°C or from-50 to +70°C In dust explosive atmospheres, they can be used in zones 21 and 22 These thermostats have explosion-proof microswitch type II2Gb, Ex dIIC according to IEC/EN 60079-1, embedded in an increased safety aluminum enclosure according to IEC/EN 60079-7. Temperature range:numerous from -25 to +300°C See more of this product Download PDF Access full catalogue |
 Type Y96Explosion proof thermostats and limiters, connection inside EX « e » aluminum housing with built-in connection block. Rod thermostat. Main features: They are intended to monitor or control the temperatures in hazardous areas. Thermostat, housing and terminal block are indivisible. In gas explosive atmospheres, they can be used in zones 1 or 2 in the presence of gas, smoke and fog, class IIC, surface temperature T6, and ambient temperature on the enclosure from -50 to +60°C, or from -50 to +70°C. In dust explosive atmospheres, they can be used in zones 21 and 22 These thermostats have explosion-proof microswitch type II2Gb, Ex dIIC according to IEC/EN 60079-1, embedded in an increased safety aluminum enclosure according to IEC/EN 60079-7. Temperature range:numerous from -25 to +300°C See more of this product Download PDF Access full catalogue |
 Type ZEPositive pressure switches, for printed circuit, creep action contact. Main features: Electronic printed circuit. This pressure switch is more sensible than snap action models and can be calibrated at lower pressure values. Very small differential. See more of this product Download PDF Access full catalogue |
 Type ZAPositive pressure switches, creep action contact. Main features: Electronic circuits. Pressure sensing on water heaters. This pressure switch is more sensible than snap action models and can be calibrated at lower pressure values. Very small differential. See more of this product Download PDF Access full catalogue |
 Type ZQSnap action contact miniature pressure switch. Rating up to 25A Main features: Pressure sensing on water heaters, boilers, and electrical appliances. See more of this product Download PDF Access full catalogue |
 Type ZWSnap action double pole contact miniature pressure switch. Main features: Pressure sensing on water heaters, boilers, and electrical appliances. See more of this product Download PDF Access full catalogue |
 Type MA1Snap action contact pressure switch, field adjustable, IP65 housing. Main features: Pressure sensing on water heaters, boilers, spas and swimming pool heaters and filters, electrical appliances used outside. See more of this product Download PDF Access full catalogue |
 Type MN3Snap action contact pressure switch, field adjustable, 3 contacts. Main features: Pressure sensing on water heaters, boilers, spas and swimming pools heaters and filters, electrical appliances (For incorporation). See more of this product Download PDF Access full catalogue |
 Type ZHDifferential pressure switch for printed circuits. Main features: Electronic printed circuits. Detection of low positive, negative or differential pressure. Measurement of liquid levels, air flow, filters efficiency. Very small differen¬tial, about 2 millibars See more of this product Download PDF Access full catalogue |
 Type ZPSnap action contact airswitch. Main applications: Direct actuating of pumps and blowers in spas and swimming pools, sink erasers, professional or home appliances used with risks of water splashing. Resist to spas and swimming pools ozone concentration. See more of this product Download PDF Access full catalogue |
 Type 66ZM5 Air buttons (air transmitters). Main features: Remote operation of air switches. This pneumatic switching technology safely isolates the user from the electrical current. The air transmitters provide the pulse air pressure needed to operate a remote air switch Typical applications: Spas , swimming pools, electrical equipment remote operating of electrical devices on/off including motors, lights, pumps, air blowers, or other associated equipment. Operating distance: With appropriate tubing, these hand actuation transmitters can operate air switches from distances of up to 30 meters (100 feet.) See more of this product Download PDF Access full catalogue |
 Type 66ZMDFoot air pedal (air transmitters). Main features: Remote hand free operation of air switches. Even in wet or hazardous environments, this pneumatic foot air pedal safely isolates the user operating power tools and other electrical devices from the electrical current. The foot air pedal provide the pulse air pressure needed to operate a remote air switch Two switching logics are possible, depending of the air switch used: - Momentary Switching: Press and hold for on, release for off - Alternate Action Switching: Press for on, press again for off Typical applications: Electrical equipment remote operating of electrical devices on/off including motors, lights, pumps, air blowers, or other associated equipment. See more of this product Download PDF Access full catalogue |
 Type R1BPaddle flow switches, micro-switch contact; 3/4” BSPP union nut. Main features: Water flow detection on water pipes Functional principle: Balanced paddle, perpendicular to the main flow, actuating a micro- switch. Flexible elastomeric gasket between paddle and electric switch See more of this product Download PDF Access full catalogue |
 Type R1DPaddle flow switches, micro-switch contact; 1/2” BSPP male thread. Main features: Water flow detection on water pipes Functional principle: Balanced paddle, perpendicular to the main flow, actuating a micro- switch. Flexible elastomeric gasket between paddle and electric switch See more of this product Download PDF Access full catalogue |
 Type R1QPaddle flow switches, micro-switch contact, 1/2” BSPP male thread, and Pt100 temperature sensor. Main features: Water flow detection on water pipes, with simultaneous water temperature measurement Functional principle: Balanced paddle, perpendicular to the main flow, actuating a micro- switch. Flexible elastomeric gasket between paddle and electric switch. Temperature measurement is made by a plastic pocket located under the ½” thread See more of this product Download PDF Access full catalogue |
 Type R1PPaddle flow switches, reed switch contact, 3/4”union nut, slim design. Main features: The most simple flow switch with magnetic pull-back. Recommended mounting position is on horizontal pipes, but can be mounted in any position. For water flow detection on dia. 25 to 100 mm water pipes See more of this product Download PDF Access full catalogue |
 Type R1QPaddle flow switches, reed switch contact, inside barbed tee for 1”soft tube. Main features: Tee equipped with paddle flow switch, for spas and swimming pools applications, mounting on 1” (20 to 21mm ID) soft PVC tubes, adjustable setting. Used on water circulation circuits to detect the passage of water or filter clogging and avoid dry running. Recommended mounting position is on horizontal pipes, but can be mounted in any position allowing an efficient air bleed. See more of this product Download PDF Access full catalogue |
 Type R1XPaddle plastic switches, reed switch contact, external body. Main features: General application in flow detection. . Recommended mounting position is on horizontal pipes, but can be mounted in any position. For water flow detection on dia. 15 to 100 mm water pipes See more of this product Download PDF Access full catalogue |
 Type R1VPaddle flow switches, reed switch contact; external brass body. Main features: General application in flow detection. Recommended mounting position is on horizontal pipes, but can be mounted in any position. For liquids flow detection on dia. 15 to 100 mm pipes. Body and union nut in brass for improved mechanical strength and pressure resistance. Connection box with terminal block or connectors, and detection point adjustment screw See more of this product Download PDF Access full catalogue |
 Type R36Piston flow switches, reed switch contact, inlet and outlet 3/4” BSPP male. Main features: Product developed for electrical or gas instantaneous water heaters. 3/4 “ BSPP male water inlet and outlet. Mandatory vertical mounting, with water inlet from the bottom. Built-in over-pressure valve See more of this product Download PDF Access full catalogue |
 Type DMVertical mounting level switch, reed switch contact, polypropylene stem with M8 thread, dia. 20 x 16.4 mm EPS foam float. Main features: vending machines, air conditioning pumps, dehumidifiers. Small diameter float for reduced space applications. EPS foam float avoid float leaks, but reduces the maximum liquid temperature. See more of this product Download PDF Access full catalogue |
 Type DTHorizontal mounting level switch, reed switch contact, PBT stem, hollow PBT float, ½”NPT thread. Main features: steam generators, coffee machines, vending machines, air conditioning pumps, dehumidifiers, tanks. The side mounting allows to adjust the level on big size tanks. See more of this product Download PDF Access full catalogue |
 Type Q88FMechanical humidistats for incorporation, front shaft adjustment. Main features: They use hygroscopic polymer film with special treatment, guaranteeing a fast response, long lifetime and high stability SPDT or SPST contact See more of this product Download PDF Access full catalogue |
 Type Q88SMechanical humidistats for incorporation, side shaft adjustment. Main features: They use hygroscopic polymer film with special treatment, guaranteeing a fast response, long lifetime and high stability SPDT or SPST contact See more of this product Download PDF Access full catalogue |
 Type Q88F-RWall mounting mechanical room humidistats, Universal use. Main features: They use hygroscopic polymer film with special treatment, guaranteeing a fast response, long lifetime and high stability SPDT contact See more of this product Download PDF Access full catalogue |
 Type Q7CDIN rail mounting miniature humidistat for cabinet air control. Main features: This humidistat is designed to switch on a heater or a ventilating fan It can also be used to switch on humidifiers, dehumidifiers, or other devices. It must be mounted in a ventilated area. See more of this product Download PDF Access full catalogue |
 Types: Q8WHHElectronic on-off relative humidity and temperature controllers with IP 65 enclosure for green house and farms. Main features: Temperature and relative humidity display or control in cold rooms commercial applications, green house and farming See more of this product Download PDF Access full catalogue |
 Type 5EAFire detection fusible links 2 holes dia 11.5mm distance 43.5mm. Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value. See more of this product Download PDF Access full catalogue |
 Type 5EDFire detection fusible links 2 holes dia 5.2mm distance 16mm. Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value. See more of this product Download PDF Access full catalogue |
 Type 5EEFire detection fusible links 2 holes dia 6.9mm distance 23.7mm. Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value. See more of this product Download PDF Access full catalogue |
 Type 5EFFire detection fusible links 2 holes dia 7mm distance 95mm. Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value. See more of this product Download PDF Access full catalogue |
 Type 5EGFire detection fusible links distance 9.6mm. Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value. See more of this product Download PDF Access full catalogue |
 Type 5EHFire detection fusible links 2 holes dia 7mm distance 95mm. Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value. See more of this product Download PDF Access full catalogue |
 Type 5EJFire detection fusible links 2 holes dia 6.9mm distance 46mm. Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value. See more of this product Download PDF Access full catalogue |
 Type 5ETFire detection fusible links 2 holes dia 10.3mm distance 59.6mm. Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value. See more of this product Download PDF Access full catalogue |
 Type 5EVFire detection fusible links 2 holes dia 6.3mm distance 32mm. Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value. See more of this product Download PDF Access full catalogue |
 Type 5EWFire detection fusible links 2 holes dia 5.4mm distance 30.5mm. Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value. See more of this product Download PDF Access full catalogue |
 Type 5EZFire detection fusible links 2 holes distance 11.4mm. Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value. See more of this product Download PDF Access full catalogue |
 Type BN6 mm² Glazed ceramic connection blocks. Nickel plated connectors. Main features: Ceramic: Ker 110 glazed 5 sides. Available in 1, 2, 3, 4 poles See more of this product Download PDF Access full catalogue |
Type BV 4 mm² Glazed ceramic connection blocks. Nickel plated connectors. Main features: Ceramic: Ker 110 glazed 5 sides. Available in 1, 2, 3, 4 poles See more of this product Download PDF Access full catalogue |
Type BP 10 mm² Glazed ceramic connection blocks. Nickel plated connectors. Main features: Ceramic: Ker 110 glazed 5 sides. Available in 1, 2, 3, 4 poles See more of this product Download PDF Access full catalogue |
| Type BQ 16 mm² Glazed ceramic connection blocks. Nickel plated connectors. Main features: Ceramic: Ker 110 glazed 5 sides. Available in 1, 2, 3, 4 poles See more of this product Download PDF Access full catalogue |
 Type BCHigh Temperature (500°C) Ceramic Terminal Blocks, with Stainless Steel terminals and screws. Main features: These high quality electrical connection blocks allow efficient and easy wiring connections of ovens, infrared heaters, quartz tube heaters in furnaces, kilns, catering equipment. • Designed for increased resistance to permanent high temperature, they can withstand long term temperatures of 900°F (500°C) and 1292°F (700°C) during short time periods. • Terminal screws are provided with a stainless steel elastic washer to avoid loosening by thermal cycles • Rating: 32A per terminal Available in 2 and 3 pole See more of this product Download PDF Access full catalogue |
 Type BDHigh Temperature (500°C) Ceramic Terminal Blocks, with Stainless Steel terminals and screws, heat conduction protection, and wire protection. Main features: These high quality electrical connection blocks allow efficient and easy wiring connections of ovens, infrared heaters, quartz tube heaters in furnaces, kilns, catering equipment. • Designed for increased resistance to permanent high temperature, they can withstand long term temperatures of 900°F (500°C) and 1292°F (700°C) during short time periods. • This BD type has 4 legs to avoid thermal conduction with the mounting board and a cable bending protection blade on saddles • Terminal screws are provided with a stainless steel elastic washer to avoid loosening by thermal cycles • Rating: 32A per terminal Available in 2 and 3 pole See more of this product Download PDF Access full catalogue |
 Type BEMHigh temperature grommet. Main features: High temperature ceramic cable grommet for kilns. Metal nut. Maximum temperature 300°C See more of this product Download PDF Access full catalogue |
 Type BRMultiple poles ceramic connection blocks. Main features: Designed for increased resistance to permanent high temperature, they can withstand long term temperatures of 900°F (500°C) and 1292°F (700°C) during short time periods. • Saddle terminals screws are provided with a stainless steel elastic washer to avoid loosening by thermal cycles • Rating: 32A per terminal See more of this product Download PDF Access full catalogue |
 Type BYCylindrical connection block. Main features: 3 ways ceramic block. Nickel plated brass M3 screw terminal, without pressure plate, for wires up to 3mm maximum diameter. Maximum temperature 230°C See more of this product Download PDF Access full catalogue |
*ULTIMHEAT ® is a registered trademarkTemperature Controls and Safety Devices: Creep action fixed setting strip thermostat / Snap action fixed setting strip thermostat / Snap action fixed setting disc thermostat / Thermal Fuses / Thermocouple / Resistance Temperature Devices (RTD) / Bulb and Capillary Control/ Bimetal surface control/ Remote bulb thermostat/ Remote electric temperature control
Silicone Flexible Heating Surface Heater Manufacturer and ULTIMHEAT Product Distributor in Thailand and ASEAN Morning Dew Building, 41/3 – 41/4 Soi Sukhumvit46 Sukhumvit Rd. Phrakanong Klongtoey Bangkok 10110 Thailand Tel. +66(0)27135196 / Fax. +66(0)27135197 E-mail: infoblueink@ultimheat.com / Website: www.ultimheat.co.th |